Monarch6017HandiPrintPrinterTC6017OI Rev. AB 4/01 ©2000 Monarch Marking Systems, Inc. All rights reserved.
1-6 Getting Started Reading the LED This table explains the LED indicator. LED Indicator Status Red On The charger is charging the battery at a fa
Getting Started 1-7 Connecting the Printer Attach the handheld to the printer's 14-pin connector as shown. The handheld’s bottom lip fits snugly
1-8 Getting Started 3. Using the grommet provided, secure the strap into the attaching hole. 4. Thread the strap through the slot and secure the stra
Loading Supplies 2-1 LOADING SUPPLIES The printer can print text, bar codes, and some limited graphics on thermal direct receipt paper. See Appendi
2-2 Loading Supplies 2. Drop the supply into the well. Make sure the supply unwinds from the top as shown. 3. Position the supply between the prin
Using the Printer 3-1 USING THE PRINTER This chapter includes information about printing, using the magnetic stripe reader, and scanning bar codes.
3-2 Using the Printer Quickly swipe the card through the reader either left-to-right or right-to-left with the magnetic stripe in the reader. The
Using the Printer 3-3 Scanning Bar Codes Scanning bar codes is application specific. You should only scan a bar code when prompted by your applicati
3-4 Using the Printer Scanning Tips ♦ Make sure there are no voids in the bar code symbol. ♦ Hold the scanner four to eight inches from the bar c
Cleaning 4-1 CLEANING You may need to clean the printhead and platen roller after printing approximately six rolls of supply, whenever you load new
Each product and program carries a respective written warranty, the only warranty onwhich the customer can rely. Monarch reserves the right to make c
4-2 Cleaning 4. Clean the platen roller with a dry cloth or small brush. You can also use another cotton swab moistened with isopropyl alcohol. Tu
Troubleshooting 5-1 TROUBLESHOOTING If you cannot fix a problem, call Technical Support. Problem Action Does not feed or has a paper jam. Remove an
5-2 Troubleshooting Problem Action Light/heavy printing or voids in printing. Clean the printhead. Check or recharge the battery. See “Charging t
Specifications A-1 SPECIFICATIONS Printer Specifications Height: 2.8 inches (71 mm) Width: 4.25 inches (108 mm) Length: 9.5 inches (241 mm) Weigh
A-2 Specifications Charging Time: Approximately 3 hours with no printing Communications: RS-232 port Print Ratio 25% black maximum per square inch S
Specifications A-3 Using the Optional Stand Read the following if you purchased the optional printer stand. The stand can be ♦ used on a table top
A-4 Specifications For Wall-Mounting: Wall-mounting hardware is not included. Use two screws or nails that support at least 5 pounds (2.3 kg.). 1.
For supplies, service, or assistance call :1-800-543-6650 (In the U.S.A.)021 869 97 70 (In Switzerland)www.gomaro.ch
i TABLE OF CONTENTS GETTING STARTED... 1-1 Unpacking the Printer ...
Getting Started 1-1 GETTING STARTED Use these operating instructions with your Monarch 6017 HandiPrint Printer. The printer works with the SYMBO
1-2 Getting Started Battery and Safety Information The printer is powered by a 7.4V Lithium Ion (LiIon) battery. There are no memory effects with L
Getting Started 1-3 3. Open the strap at the VELCRO tab and pull the strap through the slot. You now have access to the battery door. Move the str
1-4 Getting Started 6. Insert the battery into the printer as shown. 7. Press the battery into place. 8. Lock the battery door by pushing up the batt
Getting Started 1-5 You can print while the battery is charging; however, the battery may not receive a full charge. You can also charge the handheld
Komentáře k této Příručce