Paxar 9445 Uživatelský manuál

MTC9445EM Rev. D 7/95©1988 Monarch Marking Systems, Inc. All rights reserved.Equipment Manual

2.Turn the printhead lever to the left to release the printhead.3.Hold down the lower supply guide and rewind the oldsupply roll, if there is one.4.Re

5.Push the lock to the right to unlock the outer supply holderand remove the outer supply holder from the supply shaft.Remove the old supply core, if

6.Place the new supply roll on the supply shaft as shown.NOTE:If your supply has a 3-inch (76.2 mm) core:a.Remove the hub from the inner supply holder

8.Turn the outer supply holder so the lock faces out. Alignthe supply holder tabs with the tracks on the shaft.9.Push the supply holder onto the supp

11.Pull enough supply from the roll to reach the printhead.12.Hold down the lower supply guide.13.Feed the supply past the out-of-stock switch, betwee

15.To adjust for wide or narrow supply, turn the supply widthadjustment knob to:•NARROW for supply two inches in width or smaller.•WIDE for supply gre

17.Turn the printer on. If you are:•replacing the supply with a new roll of the same size,press f to align the printer.•changing supply size, adjust

3. If you are reloading supply:a.Cut the backing paper in front of the paper take-upspool, and then manually rewind the supply roll.b.While holding th

6.Place the new supply roll on the supply shaft as shown.NOTE:For 3-inch (76.2 mm) cores:a.Remove the hub from the inner supply holder.b.Reverse the o

8.Turn the outer supply holder so the lock faces out. Alignthe supply holder tabs with the tracks on the supply shaft.9.Push the supply holder onto t

Each product and program carries a respective writtenwarranty, the only warranty on which the customer can rely.Monarch reserves the right to make cha

11.With one hand, hold down the lower supply guide. Withthe other hand, feed the backing paper between the lowerand upper supply guides, past the pri

14.Turn the supply roll counterclockwise to remove anyslack in the backing paper. Your supply and backing papershould be fed as shown.LabelsBacking P

15.To adjust for wide or narrow supply, turn the supply widthAdjustment Knob to:•NARROW for supply two inches in width or smaller•WIDE for supply grea

17.Turn the printer on. If you are:•replacing the supply with a new roll of the same size,press f to align the printer.•changing supply size, adjust

Loading Fan-Fold SupplyThe 9445 has the ability to print fan-fold supply with theoptional fan-fold printer cover. If your printer does not have afan-

6.With one hand, hold down the lower supply guide. Withthe other hand, feed the backing paper between the upperand lower guides, past the printhead,

Adjusting the Supply SensorThe supply sensor controls how much supply feeds betweentags or labels. The sensor reads black marks or feed apertures.To

Die cut supply requires no sensor adjustment.1.Do one of the following:For black mark supply, turn the sensor adjustment knobcounterclockwise until it

Adjusting the On Demand SensorThe On Demand sensor stops the printer between tags orlabels when you print in the On Demand mode. The sensordetects th

3. Loading a RibbonThere are two types of supplies:Thermal Directspecially treated thermal supplies thatdon’t use a ribbon for printing.Thermal Transf

PrefaceThis manual contains information about the general setup andmaintenance of the 9445 printer. Some of the features in thismanual may not be av

Loading a Ribbon RollTo load a ribbon roll:1.Open the front panel.2.Turn the printhead lever to the left to release the printhead.(Also see the supply

4.Pull the ribbon spool holders off. Remove the old ribbon (ifthere is one).5.Be sure the thermal supply indicator is pointing upward.NOTE:Turn the t

7.Guide the new ribbon around the rollers on the ribbon rolladapter. Slide the upper spool onto the upper spool shaft.8.Slide the ribbon spool holder

11.Turn the upper ribbon spool clockwise until the black partof the ribbon is past the feed mark.12.If the printer has supplies loaded for continuous

Loading a Ribbon CassetteTo load a ribbon cassette:1.Open the front panel.2.Turn the printhead lever to the left to open the printhead.(Also see the s

4.Remove the new ribbon cassette from the package. Thenloosen ribbon from cassette as shown below.Loading a RibbonRoll 3. Loading a Ribbon3-7

5.Guide the edge of the ribbon around the ribbon guide post.6.Place the cassette on the ribbon spools and push itagainst the back wall. The spool loc

4. Adjusting the DisplayThe intensity adjustment wheel is on the right side of thekeyboard. Rotate the wheel to lighten or darken the display.NOTE:S

9445 Equipment Manual4-2

5. Cleaning the Printhead and Platen Roller1.Open the front panel.2.Turn the printhead lever to the left to open the printhead.3.Wind the supplies

9445 Equipment Manualii

5.Lightly moisten a cotton swab with alcohol and rub it backand forth across the printhead. Clean the platen roller thesame way.6.Reload the supply a

Appendix A. Converting theKeyboard for Table Top Use1.Lift the keyboard from the printer and place it on the table.2.Turn the keyboard over and remove

9445 Equipment ManualA-2

Appendix B. TroubleshootingIf you cannot fix a problem, call Monarch service."Head Test Failure" MessageThe 9445 performs a printhead test w

Start-Up and PrintingProblem ActionError message appearsduring start-up.Turn power off, then on and try again.If an error message appears again,call M

Start-Up and Printing (continued)Problem ActionPrinted data becomesmisaligned.Recalibrate the printer. Select PrinterOptions from the main menu, then

CuttingProblem ExplanationCut length is more than0.03 inches from taglength.Call Monarch Service."Knife jam" messageappears.Paper is jammed

Appendix C. SpecificationsPrinterHeight:14.5 inches (368.30 mm) withoutkeyboard; 17.7 inches (449.58 mm) withkeyboard.Weight:35 lbs. (15.88 kg) packag

Print SpeedWith ribbon:•Bar code toward top/bottom of tag3.6 IPS•Bar code toward left/right side of tag2.5 IPSPrint SpeedWithout ribbon:•Bar code towa

Table of Contents1. Installing the Printer... 1-12. Loading Supply...

For supplies, service, or assistance call:TOLL FREE:1-800-543-6650 (In U.S.A.)1-800-263-4650 (In Canada)Printed in U.S.A.

Appendix C. Specifications...C-1Printer...

1. Installing the Printer1.Place the printer on a level surface.2.To install the keyboard on top of the printer:a.Remove the cord from the base of the

3.Turn the power switch off and insert the power cord intothe socket. Plug the other end of the cord into agrounded 115 VAC electrical outlet.NOTE:If

2. Loading SupplyThe printer prints both tags and labels. The supply may bewound with the printable side on either the inside or theoutside.This chap